[GUIDE] Cara memberikan thermal paste dengan benar pada processor

[GUIDE] Cara memberikan thermal paste dengan benar pada processor

---

Pasta:

karena ini sumbernya dari website Arctic Silver, dan ada banyak merk thermal paste lain, dan yg lain mungkin memberi instruksi yg beda dari instruksi Arctic Silver. Guide ini berdasarkan dari Arctic Silver 5 karena biasanya pasta yg di rekomen di web review2.

Pembersihan:

Penting: sebelom mulai pastikan permukaan heatsink dan processor sudah bersih. pembersihan bisa pakai Iso-Propyl Alcohol atau Arctic Silver ArctiClean. Gunakan kain yg halus seperti kain untuk ngelap kacamata untuk membersihkan permukaan dengan pembersih untuk memastikan permukaan sudah bersih dari residu, dan jangan pegang sama skali permukaan yg sudah bersih.

Pengaplikasian:

Intel :

Spoiler for Single Core:

Sebelum:
Sesudah dipasang HSF:
-buat Intel P4 sebesar 1 butir beras
-buat AMD 64 sebesar 1.5 butir beras

Spoiler for Dual Core

buat mastiin, cek kalo segitiga kecilnya ada di bawah kiri, kasih pastanya dari atas ke bawah

harus berbentuk garis karena bentuk corenya kek gbr yg di bawah

Spoiler for Quad Core:

seperti dual core, cuma ini horizontal, buat mastiin, cek kalo segitiga kecilnya ada di bawah kiri

harus berbentuk garis horizontal karena bentuk corenya kek gbr yg di bawah

Spoiler for Core i7:

seperti di gambar

AMD:

Spoiler for Single Core:

lihat di bagian intel single core, perbedaan hanya pada besar pasta

Spoiler for Dual Core:

besar pasta 1.5 butir beras

Spoiler for Quad Core:

sama seperti AMD Dual Core

Finishing:
cek kembali untuk memastikan kalau tidak ada kontaminasi dari debu atau benda lain di HSF atau di heatspreader processor. pasang HSF pada processor sesuai dengan instruksi HSF itu sendiri. Pastikan pada pemasangan HSF, turunkan HSF sejajar ke processor.
Ketika HSF sudah nempel dgn benar, pegang HSF dan dengan sangat lembut putar sedikit searah jarum jam sekali dan sebaliknya sekali (Hanya sekitar 1-2 derajat perputaran). Catatan: ada beberapa HSF yg tidak dapat di putar2 saat dipasang. tetapi, tes kita telah menunjukkan bahwa cara ini meminimalisasi kemungkinan adanya gelembung udara dan kekosongan antara processor dengan HSF.

FAQ:
Kenapa kok cuma sedikit/ga semua permukaan di balutin pasta?
karena sebagian besar panas dari core processor berjalan langsung menembus IHS, karena itu lebih efektif mempunyai pasta yang terpusat di atas CPU core dari pada seluruh IHS di tutupi pasta dari ujung ke ujung

akhir kata: semoga bermanfaat

disadur dari: ini dan ini

XBOX 360's Error

XBOX 360’s Error

---

Saya mau sharing info mengenai XBOX 360 elite-falcon dan non falcon 3rol atau 3RROD atau Red Ring Of Death…

Saya dapet link dari sini…..

Ada yang 1 lampu RROD, ada yang 2, 3, dan 4…. (Gak mungkin lah, lebih dari 4 )

Spoiler for Ini contoh untuk 1 lampu:

Spoiler for Ini contoh untuk 2 lampu:

Spoiler for Ini contoh untuk 3 lampu:

Spoiler for Ini contoh untuk 4 lampu:

Sebenernya sich, thermal coatnya (liquid penghantar panas) yang non-falcon pada suhu yang tinggi akan mencair dan membuat transfer panas processor TERHAMBAT…

Untuk yang falcon, heatsinknya pake sistem metal pipe,, jadi apabila thermal coatnya mencair maka tidak seperti non-falcon…

SOLUSI-SOLUSI…
non-falcon:> Penggunanya harus tahu perkiraan thermal coatnya harus diganti!!!

falcon:> Penggunanya mempunyai rentang waktu yang cukup lama untuk maintenance thermal coatnya… JANGAN TUNGGU SAMPE RROD KELUAR!!!

Jadi BUKAN berarti yang FALCON bisa maen lama TANPA memperhatikan THERMAL COATNYA…..

he..he..he..

Error Code

System Error.  Contact Xbox Customer Support.

(Above photo taken from Xbox-Scene.com article)

---

The following re-Posted on Llamma with permission 05/02/06 Updated 05/08/07
Originally posted in Xbox-Scene.com Forums http://forums.xbox-scene.com/index.php?showtopic=484726 (Check out the forum post for the most up to date info)

Written By:	Contributions By:
twistedsymphony	posure diacronic XGC xINSANITYx sowa99 tommiwan	Team Modfreakz neoed30 Xfab29 rsintx BenS leorimolo	CajunSniper gwashington42490 G0t M4xx 21 mp3boy bluefalcon ethylique	MatrixNeo sodiumba Taher

---

THIS ERROR CODE GUIDE IS IN NO WAY OFFICIAL NOR DO WE MAKE ANY CLAIMS TO IT’S ACCURACY.

100% of the info here was discovered by Scene Members through trial and error, a lot of the information is probably incorrect, but it is our best guess. If you discover something that is incorrect or not included please PM twistedsymphony to update the guide. Neither Xbox-Scene, twistedsymphony, nor any of the guide contributers take responsibility for any actions you might take as a result of reading this guide.

–==ERROR Codes==–

If there is a problem with the Xbox360 The LEDs in the ring of light will flash in a particular pattern. The pattern itself leads some insight to the problem. Certain patterns will lead to numbered error codes which will provide further insight to the problem. The numbered error codes are described below their corrosponding LED code.

After reading this guide if you’d like to discuss the problems you’re experiencing with others you can do so in the following thread:
http://forums.xbox-scene.com/index.php?showtopic=462099

these are the codes we know so far…
Please contribute if you know of new codes that are not part of this list.

=============================

Sections 1, 2, 3, and 4 are flashing red

– The AV cable cannot be detected

/ \
\ /

THINGS TO TRY

1. Make sure that the AV cable is correctly connected to the Xbox 360 console.
2. Disconnect the AV cable from the Xbox 360 console, and then reconnect the AV cable to the Xbox 360 console.
3. If the four flashing red lights continue to flash, try wiping the metal area of the AV pack with a dry cloth. The metal area is the end that plugs into the console. Wipe the metal area thoroughly, and then try the AV Pack again.
4. If the AV cable is correctly connected but the four red lights are still flashing, substitute a different AV cable if you have one available.

=============================

Sections 1, 3, and 4 are flashing red

– General Hardware Failure

/ \
\ /

Check out this tutorial!  If you are getting the 3 Red Light Fix (AKA Three Red Lights of Death, 3RLOD, Red Ring of Death, X-Clamp Fix) This link has the information you need!!

Check the secondary Error Code per the instructions in the section below

THINGS TO TRY

1. Try restarting the console.
2. If restarting the console does not resolve the behavior, follow these steps:
   • Turn the console off.
   • Unplug all the power and AV cables from the console.
   • Unplug the power cord from the wall socket.
   • Firmly reconnect all the cables.
   • Turn on the console.
3. If these steps do not resolve the behavior, turn the console off, remove the hard drive, and then turn on the console. If the 3x Red LED error light is no longer displayed, turn the console off, re-attach the hard drive, and then turn on the console.
4. Also examine the lights on the power supply. When you turn on the console, the power supply light should illuminate green even if the three lights on the RoL flash red.

=============================

Sections 1, and 3 are flashing red

– Overheating

/ \
\ /

Alternativly Overheating can be cause by the console locking up or “freezing” after a set amount of time. Lockups that occur at a specific point in a game are generally problems with the game itself and not caused by overheating.

THINGS TO TRY

1. Let the Xbox 360 console cool.
   Note You may have to wait several hours for the console to cool enough. Do not turn on the console when the console is hot.
2. Verify that the console has sufficient ventilation and that the fan is operating. For more information about ventilation, see the “More Information” section.

PREVENTION SUGGESTIONS
To try to prevent this problem, use the following precautions:

• Do not block any ventilation openings on the Xbox 360 console.
• Do not put the Xbox 360 console on a bed, on a sofa, or on any other soft surface that may block ventilation openings.
• Do not put the Xbox 360 console in a confined space, such as a bookcase, a rack, or a stereo cabinet, unless the space is well-ventilated.
• Do not put the Xbox 360 console near any heat source, such as a radiator, a heat register, a stove, or an amplifier.

DO NOT EVER PUT YOUR CONSOLE IN THE FREEZER OR OUT IN COLD WEATHER
Some people think that doing this might help “fix” an overheating console, in fact doing so could cause even bigger problems. Electronic devices like your console are made to function at and around room temperature, extreme cold temperatures can often cause just as many problems as extreme warm temperatures (such as overheating). Also if the console is located in a dramatically cold area while running, the difference in temperature between the hot console and cold air can create condensation which in turn will short out your console making the situation far worse. Condensation will happen more quickly if your console is overheating due to the greater difference in temperature. In short… DON’T DO IT.

A more agressive Solution to overheating is to improve the cooling system of the console. The best solution is to replace the thermal compound. If you attempt this you do so at your own risk. If you’re console is still underwaranty it is recomended that you contact MS for a replacement before attempting to fix it yourself.

=============================

Section 4 is flashing red

– Hardware Failure

/ \
\ /

The Specific Type of hardware failure can be determined by the error code displayed on the screen.
If the screen is blank or you would like additional information follow the instructions for determining the secondary error code in the section below
E45: Unknown (possibly dashboard update related)

E64: DVD Drive Error…. DVD Timeout, Wrong firmware, dvd is without f/w chip, etc.

E65: DVD Drive Error…. DVD Timeout, Wrong firmware, dvd is without f/w chip, etc. This can also be caused by the tray not being fully closed on boot.

E66: DVD Drive Error: DVD model, or version does not match that of the version expected by the dashboard. OR the firmware version on the drive is older then the firmware version expected by the dashboard. Make sure the DVD drive is of the same version originally included with the console and that it is using either the original firmware included with the console or newer.

E67: Hard Drive Error… It could be a problem with the Hard Drive itself or a problem with the internal connection to the hard drive, Try removing the hard drive and playing without it

E68: Hard Drive Error… It could be a problem with the Hard Drive itself or a problem with the internal connection to the hard drive, Try removing the hard drive and playing without it, This can also be caused by a Hard Drive Eprom Error. Some also believe this might be caused by a problem with the fans.

E69: Hard Drive Error… It could be a problem with the Hard Drive itself or a problem with the internal connection to the hard drive, Try removing the hard drive and playing without it

E71: possibly a dashboard update error, Check below in the “Console Reset Codes” for instructions. If that does not work there is no other solution and the console must be sent back to MS for repair.

E72: (not yet known)

E73: General Hardware Error: Ethernet port… this error is caused by a problem with the Ethernet port.

E74: AV cable error… There is a problem with the AV cable, try using a different AV cable. If the cable is known to be working then there is a 90% chance it’s a scaler chip problem (the “ANA” or “HANA” chip connected directly to the AV cable) in rare cases it is the GPU.

E76: (not yet known)

E79: Hard Drive Error… It could be a problem with the Hard Drive itself or a problem with the internal connection to the hard drive, Try removing the hard drive and playing without it

=============================

–==SECONDARY ERROR CODES==-
The specific type of hardware failure can be determined by a “hidden” error code

• Turn the xbox 360 on, and wait till the 3 red lights are flashing.
• Press and hold the sync up button (the small white one), while holding that button press the eject button.
• The LEDs will now blink the first number in the code (as described below).
• Release the eject button and press it again.
• The LEDs will now blink the second number of the code.
• Release the eject button and press it again.
• The LEDs will now blink the third number of the code.
• Release the eject button and press it again.
• The LEDs will now blink the forth number of the code.
• Release the eject button and press it again.
• The LEDs will go back to the 3 red flashing lights.

You should be able to determine the difference between the 3 flashing lights and the error code lights by the rate in which they flash.

Here is how you interpret the LEDs to get the code number:

• All four lights flashing – 0
• One light flashing – 1
• Two Lights flashing – 2
• Three lights flashing – 3

0001 power supply problem
0002 Network Interface problem
0003 Power problem could be the PSU could be the GPU/CPU, somehow the console isn’t getting clean power from the power supply.
0010 over heating
0011 over heating – If you are receiving this error after disassembling your console make sure to all 8 of the heatsync screws are tightened securely to the board/heatsink holes.
0012 over heating
0013 over heating
0020 (Not yet known, possibly overheating)
0021 DVD Drive Time out – Can be caused by problems with a firmware flash. This is also speculated to sometime be caused by a problem with the southbridge chipset on the motherboard.
0022 GPU Error / GPU Overheating
0023 (not yet known)
…
0101 (not yet known)
0102 unknown error

• though it’s most likely GPU related literally means the console does not know what is wrong. possibly a short or cold solder joint somewhere. So far there is 1 major theory for what causes most of these errors is that the Ram, CPU, or GPU are not soldered properly to the mother board due either to poor manufacturing or excessive heat up and cool down cycles that stress, weaken and eventually break the soldered connection.
  There are two theories to fixing this one deals with the “X” clamps that hold down the chips. The other involves re-Heating the chips. DO NOT attempt either of these if your console is still under warranty. If your console is still under warranty return it to the store where it was purchased or call MS to have it replaced. I have also heard of limited success by simply switching the AV cable from “HDTV” mode to “TV” mode.

0103 CPU Error/ CPU Overheating – see solution for error 0102
0110 Memory Error / Memory Overheating – see solution for error 0102
…
0200 (not yet known)
…
1000 (not yet known)
1001 (not yet known)
1002 (not yet known)
1003 Hard Drive Error… It could be a problem with the Hard Drive itself or a problem with the internal connection to the hard drive, Try removing the hard drive and playing without it
1010 Hard Drive Error, Can be caused buy a corrupt or missing eProm.
1011 (not yet known)
1012 (not yet known)
1013 (not yet known) possibly a dashboard update error
1020 (not yet known)
1021 (not yet known)
1022 AV cable error… There is a problem with the AV cable, try using a different AV cable. (could also be a problem with the encoder chip)
1023 DVD drive not connected, connect DVD drive to boot
1030 (not yet known)
1031 (not yet known)
1032 (not yet known)
1033 (not yet known)
…
1444 and up There is no “4” in the error codes four lights is a “0” go back and check your code again.

=============================
–==Console Reset Codes==–
Clear All Installed Game Updates and Console Cache

1. Go to the “system” blade
2. Select “memory”
3. Press Y on the HD symbol
4. Press X,X, Left Bumper, Right Bumper, X,X
5. A message will appear saying: “Do you want to perform maintenance on your Xbox 360 storage devices?”
6. Select Yes

Clear Any Failed system updates that cause the console to error.

1. With the console off, press and hold the sync up button (the small white one)
2. While holding the sync button press the power button to turn on the console
3. Continue to hold the sync button until the Console has booted up completely.
4. During the boot process the console should clear any failed updates, allowing you to use it normally.

Share Files and Printers between Windows 7 and XP

Share Files and Printers between Windows 7 and XP

Quote:

If you have a home network and are running Windows 7 and have XP on other PC(s) you might want to share files between them. Today we will look at the steps to share files and hardware devices like a printer. Sharing Files In Windows 7 and XP Sharing folders between two Windows 7 machines with the new HomeGroup feature is an easy process, but the HomeGroup feature is not compatible with Vista or XP. For this tutorial we are using Windows 7 x64 RC1 and XP Professional SP3 connected through a basic Linksys home wireless router. First make sure both machines are members of the same Workgroup which by default is named Workgroup. workgroup On the Windows 7 machine go into Control Panel \ All Control Panel Items \ Network and Sharing Center then click on Change advanced sharing settings. network and sharing advanced You will want to verify the following settings under Advanced Sharing Settings for the Home or Work and Public profile. home or work settings If you want any user to have access the public shares turn off password protection. This is located in Advanced Sharing Settings toward the bottom of the list. turn off pw If you want to keep it enabled make sure there is a log in account for the other XP machines and they have a password. create pw Now if you go into Network in Windows 7 you should see your XP machine and the Windows 7 as well which in this case is Mysticgeek-PC. Explorer To share the printer on the Windows 7 machine go into Devices and Printers from the Start menu and double click on the printer icon. devices Next double click on “Customize your printer”. 1 Printer In the Properties screen click on the Sharing Tab and check the box to share the printer and type in its share name. 2 printer share If your XP machine is an x86 OS you can install Additional Drivers before setting up the XP machine. 3 Printer add drivers To find the shared folders and devices double click on the Windows 7 machine icon under Network. Here you can see the printer connected to my Windows 7 machine is shared and also the Users Folder. shared device and users Continue into the Users folder and Public to see the shared folders, here I also created a folder called XP Share just to keep everything in central location. xpshare Over on your XP machine open up My Network Places to find the Windows 7 (mysticgeek-pc) shared folder. My Network Places Double click on the Share folder to find a list of shared folders in the Public folder on Windows 7. If you have password protection enabled you will need to type in the username and password of the user account on the Windows 7 machine first. folders Setup XP With Shared Printer To set up the shared printer in XP you will need to go into Printers and Faxes from the Start menu and kick off the Add Printer Wizard. add Printer Now select “A network printer, or a printer attached to another computer” then hit Next. network option Next select “Connect to this printer…” and type in the path for the printer connected to the Windows 7 machine and click next. print Now click Yes to the confirmation message. confirm msg Then click Finish the printer to install and complete the Wizard. Complete In some cases you will need to install the x86 XP drivers for the shared printer because the Windows 7 drivers are not compatible with XP. When everything is installed open up Printers and Faxes to find the shared printer. in explorer This should help you get started with sharing your files and other devices with your Windows 7 machine. When I first started I was able to see the printer on XP right away because I had a HomeGroup set up, but once I deleted it I needed to share the printer like you would for a workgroup. You might also have to do a couple restarts of the XP machine for it to see the shared resources on Windows 7. If you have had any experiences with sharing between Windows 7 and XP leave us a comment!

mungkin bisa di gunakan cara ini buat share antar 7, cm di rubah beberapa aja

With Pict >>

Code:

http://bebasupload.com/wlc9fy5fpxfl/Share_file_n_print_7_to_XP.rtf.html